Fuel Oil/Gas Thermal Hot Oil Heaters

Fuel Oil/Gas Thermal Hot Oil Heaters boiler takes thermal oil as medium and uses the hot oil circulating pump force the medium to make circulation; then the thermal energy will be ...

INQUIRY FEEDBACK

Product Details

Fuel Oil/Gas Thermal Hot Oil Heaters boiler takes thermal oil as medium and uses the hot oil circulating pump force the medium to make circulation; then the thermal energy will be transmitted to the heat using devices and return to the furnace to be reheated.

Because, thermal oil can get high temperature under very low pressure. So the hot oil heater can get higher working temperature at low pressure, it is a kind of safe boiler with high efficiency and low power consumption. The fuel (oil, gas) light a fire by burner to produce flame and flame goes into the internal coil to form radiation heating surface. Then it through rear coil tube forward rotated 180 ° into the tubes and to circulate into second interlayer, finally it will enter the atmosphere.

Features of Fuel Oil/Gas Thermal Hot Oil Heaters

1. It is convenient to be adjusted, and can supply balanced heat to satisfy the hard work required to precise temperature.
2. Liquid circulation heating, less heat loss, high thermal efficiency.
3. Working medium can change volume when it was heated and release heat .and we have compensation technique measures in the system.
4. We have strictly technical measures to control air, water and other low volatile matter’s content of the working medium in the circulation heating

5. The series boiler have advanced program control system, equipped with liquid level controller, pressure controller, temperature controller, and alarms to make sure the boiler work orderly and safe. So it is a kind of safe boiler with high efficiency and low power consumption.

Working Principle of Fuel Oil/Gas Fired Hot Oil Heaters

Thermal oil Heater is a new type of thermal equipment, which uses coal, or oil as fuel, takes heat conduction oil as circular media for heat supply. It is the technological flow of using high temperature circular pump to actualize forced block out circulation for the heat conduction oil; the heat conduction oil shall return to the boiler for warming up after supplied heat for heat consumption equipment. Since it can get a higher working temperature (350°C approximately) under normal pressure, carry out stable heating and precisely control the working temperature, it does not need any water treatment equipment, it has higher heat efficiency in the system, convenient in performance and maintenance; it is then the kind of safe, high efficient, energy saving heat energy supply equipment.

The reason why thermal oil boiler becomes more and more used

High temperatures up to 350°C at atmospheric pressure
Choice-free set-points of the thermal oil outgoing temperature
Supreme part-load operations
No risk of corrosion
Can be used as for both cooling below 0°C and above 100°C
Low maintenance costs (no dynamic influences, no leaking)
Quiet in operation
Easy to operate ( does not require boiler certified staff etc.)
Fluid sample analyzing that determine the condition of the system
No risk of freezing damages in cold regions.

Thermal Water & Steam Boiler requires extreme pressure in the level of high temperatures that is not economical due to high operating and owning costs. This situation paves the way for strengthening the distinctive position of Thermal Oil Boilers

Parameter Table of YYW Thermal Oil Heater

Item		YYW60	YYW120	YYW180	YYW240	YYW350	YYW470	YYW700	YYW950	YYW1200	YYW1400
Power	104kcal/h	5	10	15	20	30	40	60	80	100	120
Capacity	MW	0.06	0.12	0.18	0.24	0.35	0.47	0.7	0.95	1.2	1.4
Theraml Efficiency	%	80	80	80	80	80	80	80	80	83	84
Pressure	Mpa	0.6	0.6	0.6	0.6	0.6	0.6	0.6	0.6	0.6	0.6
Max. Temp.	°C	320	320	320	320	320	320	320	320	320	320
Circulation Oil	m3/h	10	12.5	20	20	40	60	80	100	100	100
Oil Pipe	DN	50	50	65	65	80	100	100	125	125	125
System Power	KW	5	5	5	8	10	15	20	45	55	55
Fuel		diesel.oil.gas.etc.